您现在的位置: 首页 > 产品中心 > 开关系列 > 检测开关 >
KSD-SSS-52-1 series

KSD-SSS-52-1 series

  • 产品特性
  • 应用范围

图纸下载 样品申请
KSD-SSS-52-1 series
技术特性
检测开关标准规范
电路位置1极-2个位置类型常开
额定值(最大)(电阻负载)10mA 5V DC
最大接触电阻1欧姆(初始)
使用寿命50000次循环
工作温度范围-10至+60摄氏度
储存温度范围-20至+70度
品牌:科斯达开关  KSDKG/KOSOD SWITCH/KESIDA
产品应用:医疗电器、航模、无人机、灯具照明、通讯、控制手柄、速控设备、新能源、航模设备、仪表仪器、小家电、汽车等领域

KSD-SSS-52-1 serie 备注
1.产品的外观和规格可能会被修改以提高其性能,恕不另行通知。
2.本目录仅显示外形规格。使用产品时,请获得正式规格。
3.请参阅附录[开关使用注意事项]。
4.这个杠杆开关不可清洗。
5.焊接时,应将杠杆置于自由位置,注意不要将焊剂附着在塑料部分。
6.请注意,如果在焊接过程中对端子施加应力,则可能会导致端子变形和缺陷电气性能。
7.在手动焊接时,应考虑将烙铁涂在端子的尖端,以防止出现异常未对终端施加压力
8.在电路和软件设计中,应考虑以下防止抖动和反弹的因素。读几遍。(例如5次5ms)设置延迟时间。设置积分电路。
9.对于阈值电压,建议进行中心设置。
10.应注意不要对开关主体施加应力,因为这可能会影响性能。
11.请通过模拟实际操作环境来确认高性能可靠性

KSD-SSS-52-1 series
Technical characteristics
Standard specification for detection switch
Circuit position 1 pole -2 position types normally open
Rated value (maximum) (resistive load) 10mA 5V DC
Maximum contact resistance 1 ohm (initial)
Service life 50000 cycles
Working temperature range -10 to+60 degrees Celsius
Storage temperature range -20 to+70 degrees
Brand: Coaster Switch KSDKG/KOSOD SWITCH/KESIDA
Product applications: medical appliances, model aircraft, drones, lighting fixtures, communication, control handles, speed control equipment, new energy, model aircraft equipment, instrumentation, small appliances, automobiles and other fields

KSD-SSS-52-1 serial remarks
1. The appearance and specifications of the product may be modified to improve its performance without prior notice.
2. This catalog only displays the external specifications. Please obtain formal specifications when using the product.
3. Please refer to the appendix [Precautions for Switch Use].
This lever switch cannot be cleaned.
When welding, the lever should be placed in a free position and care should be taken not to attach the solder to the plastic part.
6. Please note that if stress is applied to the terminals during the welding process, it may cause deformation and defects in the electrical performance of the terminals.
7. When manually soldering, it should be considered to apply a soldering iron to the tip of the terminal to prevent any abnormalities from not applying pressure to the terminal
In circuit and software design, the following factors should be considered to prevent jitter and rebound. Read it a few times. Set the delay time (e.g. 5ms for 5 times). Set up an integration circuit.
9. For threshold voltage, it is recommended to set the center.
10. Attention should be paid not to apply stress to the switch body, as this may affect performance.
11. Please confirm high-performance reliability by simulating the actual operating environment
0.108742s