您现在的位置: 首页 > 产品中心 > 开关系列 > 电位器 旋转开关 > 旋钮模组 >
KSD-MZ-B60C01

KSD-MZ-B60C01

  • 产品特性
  • 应用范围

图纸下载 样品申请
旋钮模组 KSD-KSD-MZ  series
Electrical characteristics电气特性
额定电流: 0.3A   0.5A  DC
额定电压 :12V     30V   50V  DC 

1. 一般事项General
1-1:适用规格Scope 本规格书适用于电子设备电子设备用微小电流回路设备,编码器开关模组。
This specification applies to encoder switch knob module for microscopic current circuits used in electronic equipment. 1-2: 标准状态 Standard atmospheric conditions 除另有规定外,测量应在以下状态下进行:
Unless otherwise specified , the standard range of atmospheric conditions for making measurements and test is as following limits: 温 度 Ambient temperature :15℃ to 35℃
相对湿度 Relative humidity :25 % to 85%
气 压 Air pressure :86KPa to 106 Kpa 1-3: 使用温度范围
Operating temperature range : -40±2℃ to +70 ℃
1-4: 保存温度范围
Storage temperature range : -40 ℃ to +85 ℃
2. 构造Construction
2-1:尺寸Dimensions 见所附成品图Refer to attached drawing
3. 额定值 Rating
3-1: 额定电压 Rated voltage :DC. 5V
3-2:Maximum operating current of encoder switch(resistive load)编码器开关最大额定电流(阻抗负载):10mA
3.3:Maximum operating current digital tube (resistive load)数码管最大额定电流(阻抗负载):30mA
4. Function 功能
4-1、Press the switch in the middle of the knob 旋钮中间按压开关
4-2、Round digital tube in the center of the knob (Applicable to digital tube knob module) 旋钮中间带数码管(适用于带数码管旋钮)
5. 使用注意事项 Application Notes
5-1:不要在高温、多湿及腐蚀性气体环境中保管。
During operation storage in high temperature and in corrosive gas.should be avoided. 5-2: 对编码器脤冲数的处理、设计时, 要充分考虑速度、脤冲调制时间和杂音干扰等因素。
As design of the pulse count process. Care should be taken with operational speed. 5-3:本制品在卡点上使A相在OFF 状态下比较安定,软件设计时以A相为标准
With this part detent positions we always be aligned with a-off phase.Therefore Make the a phase the
reference at the soft ware design stage. 5-4: 编码器的脤冲数处理电路建议附加滤波电路(图1)。
The circuit of the pulsecount process should be adding filter as figure(fig.1). 5-5 :本制品本体若接触水分则对脤冲波形能产生异常影响,避免直接接触水分。
This product when touching wet or water can be influence the pulse wave.
品牌:科斯达开关:KSDKG/KOSOD SWITCH/KESIDA

应用领域:灯光调节、音量调节、速度调节、新能源、航模设备、照明灯具、医疗器械、仪表仪器、小家电、无人机、汽车等
0.103499s